Arduino – SSR-25 DA Solid State Relay and DS3231 RTC Automatic Timer Lamp

Hello world! Today i made a code to automate your solid state relay as a timer with a DS3231 RTC clock and arduino.

I made this project to automate a lamp for a growing room for example, so it is used for growing periods. Between 4:00 and 22:00 for grow period during day and 16:00 to 10:00 for grow period during night.

In the video i set 17:59:45 as a time. which you can set in the code at

In the if statement at void AutomaticProgram() I set the value for the relay to be HIGH to 17 and the value for the relay to be LOW to 18 These values i set for the video demonstration. Change these values to the ones you want to use. Remember you can only use hours, or you need to change the code to also be able to read seconds and minutes. So you can only use a value between 0 and 23 using 0:00:00 to 23:00:00 will not work.

The code is very easy to understand, it simply reads the value “hour” and ignores everything after 17 as you can see in the video. The output in the serial monitor is the following below: 17:00:00 so those are hours:minutes:seconds But the Code only reads 17. The rest of the output, so :00:00 is ignored in the code

You will need 3 libraries.

DS3232RTC.h Download here: http://github.com/JChristensen/DS3232RTC
Time.h (included in arduino libraries)
Wire.h (included in arduino libraries)

I noticed some people run into a Compiling error with Time.h the fix for them was to use TimeLib.h Library.

Schematic:

SSR-25-DA
SSR-25-DA

Set up your time at these 2 lines below. After that comment them out.

the RTC will remember the time, if you do not comment out these lines the rtc will reset every time you upload.

Wire it up like the schematic and upload the code to the arduino.

Parts list.

Arduino uno.
1: Jumper wires MM/FF/MF
2: Solid state relay SSR-25 DA
3: DS3231 Real Time Clock RTC
4: Lamp with cable (optional, relay also shows if ON or OFF with a led)

Good luck!

The code:

First we add the libraries.

Then we create the datatype integer to read the value from the hours.

Next in void setup() we set the solid state relay pin to 7
at line 14 you can set the time for the RTC.
You only need to do this once!
The format is:Hours / minutes / second / day of month / month / year
After setting time upload the code.
On the next upload you need to comment out line 14 and 15 shown below.
setTime(17, 59, 45, 20, 10, 2017);//Hours / minutes / second / day of month / month / year
RTC.set(now());

The rtc will remember the time, if you do not comment out line 14 and 15 after setting the time, the RTC will reset every time you upload the code.

At the function void loop() we set the functions digitalClockDisplay(); and AutomaticProgram(); to run forever

At the function void AutomaticProgram() we set the if statements to run the automatic program between 2 values/hours.
in this example we used the value (hour()); from the function voiddigitalClockDisplay(void){
The if statements simply read the first value of the output in the serial monitor.
So in this case if 4 oclock in the midday is the value that hits, the Solid state relay will turn HIGH/ON and turn on the LAMP/Group/Or whatever device you like.
If the value = 22 the solid state relay will turn LOW/OFF. Default is low.

At the function void digitalClockDisplay(void) { we send the values to the serial monitor.
You can uncomment all of these and send them to the serial monitor if you like i just chose to use hours());
as a value to read, the rest will be ignored as you can see in the serial monitor it prints out 4:00:00 for example
but the code only reads the first value which is hours()); the rest :00:00 is ignored.

At the function void printDigits(int digits) we print the digits to the serial monitor.
You can change line 66 from : to . or , or whatever.

Subscribe to my youtube channel!

facebook-profile-picture
Danny van den Brande

http://www.arduinosensors.nl

<p>I like to code electronics, do 3D Design, Webdesign and Graphic Design.</p>

Leave a Reply

Your email address will not be published. Required fields are marked *